冷轧带钢轧辊温度场及其控制

分析了冷轧过程中工作辊的温度变化及热凸度的形成 ,提出了控制热凸度的有效手段 ,对完善板型控制系统具有重要的意义     

Decomposition of CF3CI by corona discharge

In this paper pulsed corona discharge is shown to be effective for the decomposition of CF₃Cl(Freon-13).The pressure of CF₃Cl was 2.67×10³Pa,after discharged for 2 min,39.5% of CF₃Cl was decomposed.The products were mainly CF₄,Cl₂ and CF₂Cl₂.The yield increased by adding O₂ or air.Under the same conditions,more than 94% decomposition yield was obtained if 5.32×10³Pa O₂ or air was added.The composition of products became CF₂O,Cl₂ and CF₄.While the partial pressure of O₂ or air reached 1 arm,the decomposition yield decreased to 54.5% and 48. 5% respectively.     

焙烧温度对铁覆膜砂IOCS吸附Cr(VI)的影响

采用序批试验研究了焙烧温度对铁覆膜砂(Iron Oxide Coated Sand,IOGS)吸附6价铬Cr(VI)的吸附平衡和吸附速率的影响.结果表明,铬在IOCS上的吸附平衡符合Langmuir吸附模型.低温制备IOCS具有较高吸附容量且对pH不敏感.110℃制备IOGS在pH 7的最大吸附容量(0.181 mg·g-1)远高于660℃制备10CS(0.023 m8·8-1).吸附过程符合准二级动力学模型.吸附速率随焙烧温度提高而下降.     

锂离子电池正极材料的回收及再制备

通过湿化学法从废旧锂离子电池中回收得到Li+、Co2+的硝酸溶液,以此为钴源,与Ni(NO3)2.6H2O、Mn(NO3)2按化学计量比混合,用草酸盐共沉淀法制备草酸盐前驱体,然后按Li过量5%加入Li2CO3混合,在空气中于800～950°C煅烧15 h得LiCo1/3Mn1/3Ni1/3O2,研究了煅烧温度对材料结构、形貌以及电化学性能的影响。结果表明,900℃保温15 h制备的LiCo1/3Mn1/3Ni1/3O2正极材料,为理想的(α-NaFeO2层状结构,颗粒为大小均匀的球形,在2.5～4.3 V的电压范围内,以0.1 C的恒定电流进行充放电,其首次充放电比容量分别为194.3和150.9 mAh/g,10次循环之后的容量保持率为89.9%,放电比容量为135.0 mAh/g。     

Catalysts for decomposing ozone tail gas

The preparation of immobilizing-catalysts for decomposing ozone by using dipping method was studied. XRD, XPS and TEM were used to characterize the catalysts. The three kinds of catalysts were selected preferentially, and their catalytic activities were investigated. The results showed that the catalyst with activated carbon dipping acetate( active components are Mn:Cu = 3:2, active component proportion in catalyst is 15%, calcination temperature is 200℃ ) has the best catalytic activity for ozone decomposing. One gram of catalyst can decompose 17.6g ozone at initial ozone concentration of 2.5g/m^3 and the residence time in reactor of 0.1s. The experimental results also indicated that humidity of reaction system had negative effect on catalytic activity.     

垃圾焚烧炉飞灰的低温玻璃固化初步研究

在研究我国城市生活垃圾焚烧炉飞灰的毒性特征和高温灼烧特性的基础上，试验了几种常用玻璃熔制助溶剂、烟气净化产物中的成分对飞灰的溶融温度和熔融减量的影响，以实现低温玻璃固化。实验发现受热温度越高、时间越长，飞灰减量越大；B2O3、硼砂、CaF2对飞灰助溶效果明显，而废玻璃、CaO、CaCl2能使悄灰溶融后形成的玻璃态物质地均匀、少孔。按一定比例同时加入硼砂、CaF2、废玻璃、CaO、CaCl2于飞灰中，混合物的熔融温度降到1000℃以下，大大低于飞灰自身的熔融温度（1200℃）。对该熔融物在空气中淬火形成的玻璃态物质按标准方法浸沥，选择测量了浸出液中铅、汞、镉、砷的浓度，初步发现低温玻璃态物质对重金属铅和镉具有较好的固化效果，而对汞有砷的固化效果尚不确定。     

难降解有机废水处理新技术

介绍了光氧化法、超临界氧化和低温等离子体化学三种废水处理新技术的原理,国内外研究的现状和未来的发展前景,分析了这些新技术在优化污染物废水处理方面得到工业应用所必须解决的主要技术问题.     

石墨炉原子吸收分光光度法测地面水中的铍

介绍了用石墨炉原子吸收分光光度计测定地面水中的铍的方法的建立     

An assessment of how distance and diesel oxidation catalyst will impact thermal decomposition behaviors of particles

Decomposition mass loss and pyrolysis products analyses of particles sampled at various locations along the tailpipe of a Euro-IV diesel engine were performed using a thermogravimetry in conjunction with Fourier transformation infrared spectrometry-mass spectrum. Diesel particles were collected at the same location with and without diesel oxidation catalyst (DOC) mounted on the test engine separately. The three poles in thermal gravity-differential thermal gravity images suggested that the decomposition process of diesel particles could be divided into three stages which correspond to the decompositions of lower boiling substances, higher boiling substances and soot respectively. It is noticed that no matter whether DOC was mounted or not, the further the particles were sampled away from the engine block, the lower the peak temperatures and the heavier the mass losses within the first two stages, which indicated that the soluble organic fraction in the particle samples increased and therefore lowering the activation energy of thermal decomposition. Hydroxyl, ammonia, C_xH_y fragments, benzene, toluene, and phenol were found to be the primary products of particle decomposition, which didn't change with the location of particle sample point. The employment of DOC increased the activation energy for particle oxidation and resulted in a higher peak temperature and lower mass loss within the first-stage. Moreover, the CO stretching bands of aldehyde and ketone at 1771 cm^?1 was only detected without a DOC, while the NO₂ peak at 1634 cm^?1 was solely noticed with the presence of DOC. Compared to the first-stage pyrolysis products, more polycyclic aromatic hydrocarbons and less C_xH_y fragments were seen in the second-stage.     

Heterojunctioned CuO/Cu2O catalyst for highly efficient ozone removal

In recent years, near surface ozone pollution, has attracted more and more attention, which necessitates the development of high efficient and low cost catalysts. In this work, CuO/Cu₂O heterojunctioned catalyst is fabricated by heating Cu₂O at high temperature, and is adopted as ozone decomposition catalyst. The results show that after Cu₂O is heated at 180°C conversion of ozone increases from 75.2% to 89.3% at mass space velocity 1,920,000 cm³/(g·hr) in dry air with 1000 ppmV ozone, which indicates that this heterojunction catalyst is one of the most efficient catalysts reported at present. Catalysts are characterized by electron paramagnetic resonance spectroscopy and ultraviolet photoelectron spectroscopy, which confirmed that the heterojunction promotes the electron transfer in the catalytic process and creates more defects and oxygen vacancies in the CuO/Cu₂O interfaces. This procedure of manufacturing heterostructures would also be applicable to other metal oxide catalysts, and it is expected to be more widely applied to the synthesis of high-efficiency heterostructured catalysts in the future.